November 4, 2024

Taylor Daily Press

Complete News World

‘Test all doors and pour water over the balcony’: an expert explains how to check a new building for defects |  MyGuide

‘Test all doors and pour water over the balcony’: an expert explains how to check a new building for defects | MyGuide

LiviusIf you purchase a fully finished new building, you cannot hold the seller or contractor liable for subsequent defects. After that, your purchase doesn’t fall under the Breyne Act, which provides protections for builders of new construction. Therefore, it is best to accurately display newly built houses and apartments. What should you definitely pay attention to in order to miss as few defects as possible? Livios Builder site asked Christophe Thege, spokesperson for the Confederation of Realtors of Flanders (CIB).


by Tom Dejonghe, in collaboration with Livios


Last updated:
11:51


source:
Livios.be

Ceiling and walls

Let’s start with that. Christoph Theiss begins “First check if the walls and ceiling have any irregularities.” “You don’t have to worry about microcracks: they are usually quite natural. If you paint them with elastomeric paint or touch them with acrylic sealant, you won’t see them anymore. Also try moving the gypsum board with your hand. enough.”

Do the walls and ceiling feel damp? “Don’t panic, that’s completely normal too, as long as the moisture expands evenly everywhere. A new building simply has at least 5,000 liters of construction moisture, which you have to let dry out, which can take up to two years.” Is the moisture concentrated in one place? Then the building may have a moisture problem, for example due to a leak.”

No unpleasant surprises in your new home? This is how you can rule out moisture problems in five steps.

See also  Orange raises the price of the slowest internet subscription Economy

Windows, frames and doors

“The windows should be closed permanently,” Christophe continues. “After all, even the slightest bit of water behind the joint puts you at risk of developing mold. Take a good look, too, at the glass itself: does it show any scratches? And open and close all the windows: can you do it effortlessly and without a whistling sound?”

At the same time, pay close attention to your window sills, both inside and out. “Are they properly laid out and finished all around? Do they slope a little outward, for example, so that there is no water left on them? And are they made of the right material in the right colour, as shown in the plans? If the different pieces of natural stone vary so much In color, you can definitely tell.”

Also use all doors. “Are all the locks and knobs installed correctly? Do the doors jam, creak or pull? Do they open in the right direction? Are the door frames well taped? This is also very important.”

Delivery of a new apartment: These are your rights.

Floors, terraces and tiles

It’s time to look down. “Are there any cracks or stains on the carpets and balconies? Are the tiles aligned and leveled correctly? You can check the latter by pouring water on it. No puddles are allowed. Outside, the terraces have to slope slightly so that the water can flow,” explains Christophe.

“Also check the joints of all types of tiles. Are they the right color and are they the same width everywhere? Do they show any cracks? Are there enough expansion joints inside, which is crucial in underfloor heating? And what about the panels: are they nicely finished? Beautiful, without gaps?”

See also  6.7 percent growth and electric weather

Install under floor heating: What you need to know about the different types, their operation, installation and price.

Electricity, heating and ventilation

Is everything ok so far? Then we move on to the electrical installation and central heating.

“First of all, check all the sockets: are they stuck in? Be sure to try them all on. And check if enough are installed, in the correct locations, as provided for in the plans. If necessary, you can install additional places. Small cost By themselves, but it will make life a lot easier later on. And be sure to check if the ceiling has the same number of light points as mentioned in the plans, if they are in the right places, if they are all working and if the lighting is well hidden.”

All switches must be properly terminated, especially in wet areas. But don’t worry about it, it will definitely show up during the inspection. The installed meters for electricity, gas and water will not be checked if they do not work properly and have been installed.”

“Is there a stove or fireplace? Then light it to see if there is smoke in the house. Also check if the heating is working everywhere. And let the ventilation system run for a while. Doesn’t it make a lot of noise? Is it the correct system as shown?” In specs?

Heating your home with a stove or fireplace? Weight options.

How do you practically handle all this scrutiny?

See also  Analysis: What if Bitcoin breaks this range? - BTC Live

It’s simple: don’t go house hunting on your own. “It’s best to visit a new building with an expert,” Christophe assures. “It is best to choose an experienced architect or contractor of your own choosing, so that they certainly represent your interests. By spending an extra few hundred euros on a specialist now, you will save yourself a lot of defects and headaches later.”

Read more on Livios.be:

Are you protected from hidden defects? A closer look at Bren’s Law

The expert explains: this is how you recognize and solve foundation problems

Building a new home is too expensive? Discover these four sustainable alternatives

This article was written by our partner Livios.be. Livios.be is an expert site focused on construction and renovation.